View AS1741G-T_4696461.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AS1741, AS1742, AS1743
H i g h - Sp e e d , L o w - Vo l ta g e , S i n g l e - S u p p l y, 0 . 8, Dual SPST Analog Switches
D a ta S he e t
1 General Description
The AS1741/AS1742/AS1743 are high-speed, low-voltage, dual single-pole/single-throw (SPST) analog switches. Fast switching speeds, low ON-resistance, and low power-consumption make these devices ideal for singlecell battery powered applications. These highly-reliable devices operate from a single +1.6 to +3.6V supply, and are differentiated by the type and number of switches as listed in Table 1. Table 1. Standard Products Model AS1741 AS1742 AS1743 Switch Types Two Normally Open (NO) Switches Two Normally Closed (NC) Switches One NO Switch and One NC Switch
2 Key Features
!
ON-Resistance: - 0.8 (+3V supply) - 2.5 (+1.8V supply)
! ! ! ! ! ! ! ! ! ! !
RON Matching: 0.08 (+3V supply) RON Flatness: 0.18 (+3V supply) Supply Voltage Range: +1.6 to +3.6V Switching Action: tON = 22ns, tOFF = 14ns Current-Handling: 250mA Continuous Break-Before-Make Switching (AS1743) Rail-to-Rail Signal Handling 1.8V CMOS Logic Compatible (+3V supply) Total Harmonic Distortion: 0.03% Operating Temperature Range: -40 to +85C Package Types: - 8-pin MSOP - 8-pin SOT23
The AS1743 supports break-before-make switching. With very low ON-resistance (RON), RON matching, and RON flatness, the devices can accurately switch signals for sample and hold circuits, digital filters, and op-amp gain switching networks. The AS1741/AS1742/AS1743 digital logic input is 1.8V CMOS-compatible when using a single +3V supply, and all devices can handle Rail-to-Rail signals. The devices are available in an 8-pin MSOP package and an 8-pin SOT23 package.
3 Applications
The devices are ideal for use in power routing systems, cordless and mobile phones, MP3 players, CD and DVD players, PDAs, handheld computers, digital cameras, hard drives, and any other application where high-speed signal switching is required. Figure 1. MSOP Block Diagrams AS1741
NO1 V+ NC1
AS1742
V+ NO1
AS1743
V+
COM1
IN1
COM1
IN1
COM1
IN1
IN2
COM2
IN2
COM2
IN2
COM2
GND
NO2
GND
NC2
GND
NC2
www.austriamicrosystems.com
Revision 1.78
1 - 15
AS1741 Data Sheet
- Pinout
4 Pinout
Pin Assignments
Figure 2. MSOP Pin Assignments (Top View)
NO1 1
8 V+
NC1 1
8 V+
NO1 1
8 V+
COM1 2
7 IN1
COM1 2
7 IN1
COM1 2
7 IN1
AS1741
IN2 3 6 COM2 IN2 3
AS1742
6 COM2 IN2 3
AS1743
6 COM2
GND 4
5 NO2
GND 4
5 NC2
GND 4
5 NC2
Figure 3. SOT23 Pin Assignments (Top View)
IN1 1
8 NO1
IN1 1
8 NC1
IN1 1
8 NO1
V+ 2
7 COM1
V+ 2
7 COM1
V+ 2
7 COM1
AS1741
NO2 3 6 IN2 NC2 3
AS1742
6 IN2 NC2 3
AS1743
6 IN2
COM2 4
5 GND
COM2 4
5 GND
COM2 4
5 GND
Pin Descriptions
Table 2. Pin Descriptions Pin Number Pin Name COM1 COM2 GND IN1 See Figure 2 and Figure 3 IN2 NC1 NC2 NO1 NO2 V+ Analog Switch 1 Common Analog Switch 2 Common Ground Analog Switch 1 Logic Control Input Analog Switch 2 Logic Control Input Analog Switch 1 Normally Closed Terminal Analog Switch 2 Normally Closed Terminal Analog Switch 1 Normally Open Terminal Analog Switch 2 Normally Open Terminal Input Supply Voltage. +1.6 to +3.6V Description
www.austriamicrosystems.com
Revision 1.78
2 - 15
AS1741 Data Sheet
- Absolute Maximum Ratings
5 Absolute Maximum Ratings
Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3. Absolute Maximum Ratings Parameter V+, INx to GND COMx, NOx, NCx to GND
Min -0.3 -0.3 -250 -350
Max +5 V+ + 0.3 +250 +350 362 2500 150 250
Units V V mA mA mW V mA mA C C C
Comments
COMx, NOx, NCx Continuous Current COMx, NOx, NCx Peak Current Continuous Power Dissipation (TAMB = +70C) Electro-Static Discharge Latch Up Immunity IN1, IN2 Latch Up Immunity all other Pins Operating Temperature Range Junction Temperature Storage Temperature Range
Pulsed at 1ms 10% duty cycle Derate at 4.5mW/C above +70C HBM Mil-Std883E 3015.7 methods Norm: JEDEC 17
-40 -65
+85 +150 +150
Package Body Temperature
+260
C
The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/JEDEC J-STD-020C "Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices"
Signals on pins COM1, COM2, NO1, NO2, NC1, or NC2 that exceed V+ or GND are clamped by internal diodes. Limit forward-diode current to the maximum current rating.
www.austriamicrosystems.com
Revision 1.78
3 - 15
AS1741 Data Sheet
- Electrical Characteristics
6 Electrical Characteristics
Table 4. Power Supply Characteristics Symbol V+ I+ Parameter Power Supply Range Positive Supply Current V+ = 3.6V, VINx = 0 or V+, all channels on or off Conditions Min 1.6 0.01 Typ Max Unit 3.6 1 V A
V+ = +2.7 to +3.6V, VIH = +1.4V, VIL = +0.5V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ V+ = +3.0V, TAMB = +25C. Table 5. +3V Supply Electrical Characteristics Symbol Parameter Analog Switch VCOMx, VNOx, VNCx Analog Signal Range RON RON RFLAT(ON) INOx(OFF), INCx(OFF) ICOMx(OFF) ON-Resistance ON-Resistance Match 1 Between Channels ON-Resistance 2 Flatness NOx or NCx OffLeakage Current COMx Off-Leakage Current COMx On-Leakage Current Conditions Min 0 TAMB = +25C TAMB = TMIN to TMAX TAMB = +25C V+ = 2.7V, ICOMx = 100mA, VNOx or VNCx = 1.5V TAMB = TMIN to TMAX TAMB = +25C V+ = 2.7V, ICOMx = 100mA, VNOx or VNCx = 1, 1.5, or 2V TAMB = TMIN to TMAX V+ = 3.3V, TAMB = +25C VCOMx = 0.3 or 3.0V, VNOx or TAMB = TMIN to TMAX VNCx = 3.0 or 0.3V V+ = 2.7V, ICOMx = 100mA, VNOx or VNCx = 1.5V V+ = 3.3V, VCOMx = 0.3 or 3.0V, VNOx or VNCx = 3.0, 0.3V V+ = 3.3V, VCOMx = 3.0 or 0.3V, NOx or VNCx = 3.0 or 0.3V TAMB = +25C TAMB = TMIN to TMAX TAMB = +25C TAMB = TMIN to TMAX 0.35 0.02 0.02 -1 -5 -1 -5 -2 -10 13 Typ Max Unit V+ 0.8 0.9 0.08 0.09 0.18 0.20 1 5 1 5 2 10 22 24 7 14 15 6 1 6 5 35 35 35 130 -55 -100 0.03 ns pC pF pF pF MHz dB dB % ns ns nA nA V nA
ICOMx(ON)
Switch Dynamic Characteristics tON Turn On Time
3
tOFF
Turn Off Time
3
tBBM Q COFF
Break Before Make Charge Injection
3
VNOx or VNCx = 1.5V, TAMB = +25C RLOAD = 50, CLOAD = 35pF, TAMB = TMIN to TMAX Figures 12, 13 VNOx or VNCx = 1.5V, TAMB = +25C RLOAD = 50, CLOAD = 35pF, TAMB = TMIN to TMAX Figures 12, 13 VNOx or VNCx = 1.5V, TAMB = +25C RLOAD = 50, CLOAD = 35p, TAMB = TMIN to TMAX Figure 14 (AS1743) 8-pin MSOP VGEN = 3.3V, RGEN = 0, CLOAD = 1.0nF, Figure 15 8-pin SOT23 f = 1MHz, Figure 16 f = 1MHz, Figure 16 f = 1MHz, Figure 16 Signal = 0, RIN = ROUT = 50, CLOAD = 5pF, Figure 17 f = 1MHz, VCOMx = 1VRMS, RLOAD = 50, CLOAD = 5pF, Figure 17 f = 1MHz, VCOMx = 1VRMS, RLOAD = 50, CLOAD = 5pF, Figure 17 f = 20Hz to 20kHz, VCOMx = 2Vp-p, RLOAD = 32
NOx, NCx OffCapacitance CCOMx(OFF) COMx Off-Capacitance CCOMx(ON) COMx On-Capacitance -3dB On-Channel BW Bandwidth VISO Off-Isolation Crosstalk THD
5 4
Total Harmonic Distortion
www.austriamicrosystems.com
Revision 1.78
4 - 15
AS1741 Data Sheet
- Electrical Characteristics
Table 5. +3V Supply Electrical Characteristics (Continued) Symbol Parameter Logic Input VIH Input Logic High VIL Input Logic Low IIN Input Leakage Current Conditions Min 1.5 VINx = 0 or V+ -1000 0.1 0.5 1000 Typ Max Unit V V nA
V+ = +1.8V, VIH = +1.0V, VIL = 0.4V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ TAMB = +25C. Table 6. +1.8V Supply Electrical Characteristics Symbol Parameter Analog Switch VCOMx, VNOx, VNCx Analog Signal Range RON INOx(OFF), INCx(OFF) ICOMx(OFF) ICOMx(ON) ON-Resistance NOx or NCx OffLeakage Current COMx Off-Leakage Current COMx On-Leakage Current Conditions Min 0 TAMB = +25C TAMB = TMIN to TMAX TAMB = +25C VCOMx = 0.3 or 1.5V, VNOx or VNCx = 1.5 or 0.3V TAMB = TMIN to TMAX TAMB = +25C VCOMx = 0.3 or 1.5V, VNOx or VNCx = 1.5 or 0.3V TAMB = TMIN to TMAX TAMB = +25C VCOMx = 0.3 or 1.5V, VNOx or VNCx = 0.3 or 1.5V TAMB = TMIN to TMAX ICOMx = 10mA, VNOx or VNCx = 0.9V VNOx or VNCx = 1.5V, RLOAD = 50, CLOAD = 35pF, Figures 12, 13 VNOx or VNCx = 1.5V, RLOAD = 50, CLOAD = 35pF, Figures 12, 13 VNOx or VNCx = 1.5V, RLOAD = 50, CLOAD = 35p, Figure 14, (AS1743) VGEN = 1.8V, RGEN = 0, CLOAD = 1.0nF, Figure 15 TAMB = +25C TAMB = TMIN to TMAX TAMB = +25C TAMB = TMIN to TMAX TAMB = +25C TAMB = TMIN to TMAX 1 6 2.5 -50 -100 1 VINx = 0 or V+ -1000 0.1 0.4 1000 8 ns 12 0.9 -1 -5 -1 -5 -2 -10 21 Typ Max V+ 2.5 3 1 5 1 5 2 10 30 35 20 25 ns ns Unit V nA nA nA
Switch Dynamic Characteristics tON Turn On Time
3
tOFF
Turn Off Time
3
tBBM
Break-Before-Make
3
Q VISO
Charge Injection Off-Isolation Crosstalk
5 4
8-pin MSOP 8-pin SOT23 f = 1MHz, VCOMx = 1VRMS, RLOAD = 50, CLOAD = 5pF, Figure 17 f = 1MHz, VCOMx = 1VRMS, RLOAD = 50, CLOAD = 5pF, Figure 17
pC dB dB V V nA
Logic Input VIH Input Logic High VIL Input Logic Low IIN Input Leakage Current
1. RON = RON(MAX) - RON(MIN). 2. Flatness is defined as the difference between the maximum and the minimum value of ON-resistance as measured over the specified analog signal ranges. 3. Guaranteed by design. 4. Off-Isolation = 20log10(VCOMx/VNOx), VCOMx = output, VNOx = input to off switch. 5. Between two switches.
www.austriamicrosystems.com
Revision 1.78
5 - 15
AS1741 Data Sheet
- Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
7 Typical Operating Characteristics
Figure 4. Charge Injection vs. Output Voltage; SOT23
45 40 35 30
Figure 5. Charge Injection vs. Output Voltage; MSOP
45 40 35 30
VDD = 3V
Q (pC)
Q (pC)
25 20 15 10 5 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3
VDD = 1.8V VDD = 3V
25 20 15 10 5 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3
VDD = 1.8V
VBIAS (V) Figure 6. RON vs. VCOM and Temperature; VDD = 2.7V
0.50 0.45 0.40
Temp = +85C
VBIAS (V) Figure 7. RON vs. VCOM
1.0 0.9 0.8
VDD = 1.8V
RON ( )
Temp = +25C
RON ( )
0.7 0.6 0.5
0.35 0.30 0.25 0.20 0 0.5 1 1.5 2 2.5 3
Temp = -40C
VDD = 2V VDD = 2.7V VDD = 3V VDD = 2.5V VDD = 3.3V
0.4 0.3 0 0.5 1 1.5 2
VDD = 3.6V
2.5
3
3.5
VCOM (V) Figure 8. tON/tOFF vs. Supply Voltage
24 22 20 20
VCOM (V) Figure 9. tON/tOFF vs. Temperature
25
tON/VDD = 3V
tON/tOFF (ns)
18 16 14 12 10 8 6 4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 0 -40 -15
tOFF
tON/tOFF (ns)
tOFF/VDD = 3V
tON
15
tON/VDD = 1.8V
10
5
tOFF/VDD = 1.8V
10
35
60
85
VDD (V)
Temperature (C)
www.austriamicrosystems.com
Revision 1.78
6 - 15
AS1741 Data Sheet
- Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 10. THD vs. Frequency; RLOAD = 32, VDD = 3V
0.06 0.05 0.04
Figure 11. Frequency Response
20 0 -20
Bandwidth
Loss (dB)
THD (%)
-40 -60 -80 -100 -120 0.001
0.03 0.02 0.01 0.00 1 10 100
0.1
10
1000
Frequency (kHz)
Frequency (MHz)
www.austriamicrosystems.com
Revision 1.78
7 - 15
AS1741 Data Sheet
- Detailed Description
8 Detailed Description
The AS1741/AS1742/AS1743 are low ON-resistance, low-voltage, dual analog SPST switches that operate from a single +1.6 to +3.6V supply. CMOS process technology allows switching of analog signals that are within the supply voltage range (GND to V+).
ON Resistance
When powered from a +3V supply, the AS1741/AS1742/AS1743 low (0.8, max) ON-resistance allows high-speed, continuous signals to be switched in a variety of applications. All devices have very low RON flatness (0.18, max) so they can meet or exceed the low-distortion audio requirements of modern portable audio devices.
Bi-Directional Switching
Pins NOx, NCx, and COMx are bi-directional and can be used as inputs or outputs.
Analog Signal Levels
Analog signals ranging over the entire supply voltage range (V+ to GND) can be passed with very little change in ONresistance (see Typical Operating Characteristics on page 6).
Logic Inputs
The AS1741/AS1742/AS1743 logic inputs can be driven up to +3.6V regardless of the supply voltage value. For example, with a +1.8V supply, INx may be driven low to GND and high to +3.6V. This allows the devices to interface with +3V systems using a supply of less than 3V.
www.austriamicrosystems.com
Revision 1.78
8 - 15
AS1741 Data Sheet
- Application Information
9 Application Information
Power Supply Sequencing
Proper power-supply sequencing is critical for proper switch operation. The power supplies should be started up in the following sequence: 1. V+ 2. NOx, NCx, COMx
Note: Operation beyond the absolute maximum ratings (see page 2) may permanently damage the devices.
Power Supply Bypass
Power supply connections to the devices must maintain a low impedance to ground. This can be done using a bypass capacitor, which will also improve noise margin and prevent switching noise propagation from the V+ supply to other components. A 0.1F bypass capacitor, connected from V+ to GND (see Figure 17 on page 11), is adequate for most applications.
Logic Inputs
Driving INx Rail-to-Rail will help minimize power consumption.
Layout Considerations
High-speed switches require proper layout and design procedures for optimum performance.
! ! !
Short, wide traces should be used to reduce stray inductance and capacitance. Bypass capacitors should be as close to the device as possible. Large ground planes should be used wherever possible.
Timing Diagrams and Test Setups
Figure 12. AS1741/AS1743 Test Circuit and Timing Diagram
V+ V+ VNOx VIH + 0.5V INx 0 VCOMx INx 50 GND COMx 50 35pF VNOx VCOMx 0 90% 90%
NOx
tR < 5ns tF < 5ns 50% 50%
AS1741/ AS1743
tON
tOFF
Figure 13. AS1742/AS1743 Test Circuit and Timing Diagram
V+ V+ VNCx VIH + 0.5V INx 0 VCOMx INx 50 GND tOFF tON COMx 50 35pF VNCx VCOMx 0 90% 90% 50% 50% tR < 5ns tF < 5ns
NCx
AS1742/ AS1743
www.austriamicrosystems.com
Revision 1.78
9 - 15
AS1741 Data Sheet
- Application Information
Figure 14. AS1743 Test Circuit and Timing Diagram
VS V+ V+ VS NO1 VIH + 0.5V INx 0 COM1 INx 50 GND COM2 50 VCOMx 35pF VCOMx 0 tBBM tBBM VS 90% 90% tR < 5ns tF < 5ns
NC2
AS1743
tBBM = tON(NOx) - tOFF(NCx) or tBBM = tON(NCx) - tOFF(NOx)
Figure 15. Charge Injection
V+ V+ NCx or NOx V+ RGEN VGEN AS1741 VOUT CLOAD 1000pF VOUT VOUT AS1742 VIN 0
AS174x
INx VIN 50 GND COMx
VOUT is the measured voltage due to charge transfer error Q when the channel turns off. Q = VOUT x CLOAD
Figure 16. NOx, NCx, and COMx Capacitance AS1741/ AS1742/ AS1743
V+ V+ COMx
1MHz Capacitance Analyzer As Required
INx GND
NCx or NOx
www.austriamicrosystems.com
Revision 1.78
10 - 15
AS1741 Data Sheet
- Application Information
Figure 17. Off-Isolation, On-Loss, and Crosstalk
Network Analyzer NOx or NCx
VIN
50
50
V+ V+ 0.1F
AS1741/ AS1742/ AS1743
V+ INx COMx GND
VOUT
Measure
Reference
50
50
Use 50 termination for off-isolation
Notes:
1. Measurements are standardized against short-circuit at socket terminals. 2. Off-isolation is measured between COMx and the off NCx/NOx terminal of each switch. Off-isolation = 20log(VOUT/VIN). 3. Signal direction through the switch is reversed; worst values are recorded.
www.austriamicrosystems.com
Revision 1.78
11 - 15
AS1741 Data Sheet
- Package Drawings and Markings
10 Package Drawings and Markings
The devices are available in an 8-pin MSOP package and an 8-pin SOT23 package.
Figure 18. 8-pin MSOP Package
Notes:
1. 2. 3. 4. 5. 6. 7.
All dimensions are in millimeters, angles in degrees, unless otherwise specified. Datums B and C to be determined at datum plane H. Dimensions D and E1 are to be determined at datum plane H. Dimensions D2 and E2 are for top package; dimensions D and E1 are for bottom package. Cross section A-A to be determined at 0.13 to 0.25mm from lead tip. Dimensions D and D2 do not include mold flash, protrusion, or gate burrs. Dimensions E1 and E2 do not include interlead flash or protrusion.
Symbol A A1 A2 D D2 E E1 E2 E3 E4 R R1 t1 t2 Typ 1.10 0.10 0.86 3.00 2.95 4.90 3.00 2.95 0.51 0.51 0.15 0.15 0.31 0.41 Tol Max 0.05 0.08 0.10 0.10 0.15 0.10 0.10 0.13 0.13 +0.15/-0.08 +0.15/-0.08 0.08 0.08 Symbol b b1 c c1 1 2 3 L L1 aaa bbb ccc e S Typ 0.33 0.30 0.18 0.15 3.0 12.0 12.0 0.55 0.95BSC 0.10 0.08 0.25 0.65 BSC 0.525 BSC Tol +0.07/-0.08 0.05 0.05 +0.03/-0.02 3.0 3 3 0.15 -
www.austriamicrosystems.com
Revision 1.78
12 - 15
AS1741 Data Sheet
- Package Drawings and Markings
Figure 19. 8-pin SOT23 Package
Notes:
1. All dimensions are in millimeters. 2. Foot length measured at intercept point between datum A and lead surface. 3. Package outline exclusive of mold flash and metal burr. 4. Package outline inclusive of solder plating. 5. Complies with EIAJ SC74 (6-lead version). 6. PKGST0005 (Rev B) refer to SOT23 8-lead SOT23-D-2019 (Rev C) package outline.
Symbol A A1 A2 b C D E E1 L e e1
Min Max 0.90 1.45 0.00 0.15 0.90 1.30 0.22 0.38 0.09 0.20 2.80 3.10 2.60 3.00 1.50 1.75 0.35 0.55 0.65REF 1.95REf 0 10
www.austriamicrosystems.com
Revision 1.78
13 - 15
AS1741 Data Sheet
- Ordering Information
11 Ordering Information
The devices are available as the standard products shown in Table 7.
Table 7. Ordering Information Model Markings Description Delivery Form Package
AS1741G AS1741G-T AS1741H-T AS1742G AS1742G-T AS1742H-T AS1743G AS1743G-T AS1743H-T
AS1741 AS1741 ASJL AS1742 AS1742 ASJK AS1743 AS1743 ASJM
Dual SPST Switch Dual SPST Switch Dual SPST Switch Dual SPST Switch Dual SPST Switch Dual SPST Switch Dual SPST Switch Dual SPST Switch Dual SPST Switch
Tube Tape and Reel Tape and Reel Tube Tape and Reel Tape and Reel Tube Tape and Reel Tape and Reel
8-pin MSOP 8-pin MSOP 8-pin SOT23 8-pin MSOP 8-pin MSOP 8-pin SOT23 8-pin MSOP 8-pin MSOP 8-pin SOT23
www.austriamicrosystems.com
Revision 1.78
14 - 15
AS1741 Data Sheet
Copyrights
Copyright (c) 1997-2007, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters austriamicrosystems AG A-8141 Schloss Premstaetten, Austria
Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01
For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact
www.austriamicrosystems.com
Revision 1.78
15 - 15

▲Up To Search▲

Price & Availability of AS1741G-T

	To Download AS1741G-T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .